Mobicon Systems manufactures compact straddle carriers and container handlers for manufacturers. Position containers at your production line, pack goods indoors, and eliminate loading dock dependency without disrupting your schedule.
Manufacturing sites deal with container handling pressures that are different from freight depots. Transport schedules, production windows, WHS obligations, and facility constraints all come into play at once. Mobicon straddle carriers are built to address each of them.
When a container arrives on a trailer, demurrage pressure forces your team to pack or unpack on the transporter's timetable. That disrupts production runs and pulls labour away from where it is needed most.
Purpose-built loading docks are expensive to construct and create a single point of congestion on busy despatch days. Many manufacturing facilities were not designed with container docks in mind, which makes every delivery awkward.
Exposing goods, raw materials, and forklift operators to rain, heat, or wind slows the process and raises WHS risk. Most container handling equipment cannot bring a container inside a building to allow weather-protected packing.
When containers are unloaded far from where goods are stored, forklifts make repeated long-distance runs across the yard. More forklift movements mean greater accident exposure, higher fuel use, and increased wear on your floor surface.
Traditional loading ramps are a documented WHS risk. Slippery surfaces, height differentials, and the movement of forklifts between ground level and trailer height all create conditions where incidents are more likely to occur.
Paying a side-loader for every container delivery adds cost that compounds over time with no ceiling. Once it leaves, the container cannot be repositioned on-site. There is no flexibility to move goods closer to where packing is happening.
A Mobicon straddle carrier decouples delivery from production. The container arrives, the Mobicon lifts it off the trailer and places it in the yard. When your team is ready, the Mobicon moves the container to the factory floor or packing area.
The truck pulls in, the Mobicon drives over the trailer and lifts the container clear in a single pass. The driver can leave immediately. No dock, no ramp, no waiting.
The Mobicon places the container wherever it suits operations at that moment. It does not need to go directly to a packing position. The yard absorbs arrivals without disrupting the production floor.
When your team is ready, the Mobicon picks up the staged container and positions it at the packing station, warehouse bay, or directly inside the building. Your schedule drives the process, not the transporter's.
The Mobicon 2T can bring a container through a factory roller door with 3.8 metres of clearance. The 2HL and 2HLe work under awnings with 5.8 metres clearance. Goods are packed in a controlled, sheltered environment.
Once packing is complete, the Mobicon picks up the container and holds it in the yard until the transport arrives. It then loads the packed container onto the truck in minutes, minimising turnaround time.
Multiple containers can be managed simultaneously. One at the packing station, one staged in the yard, one being loaded. The operation becomes calmer and more predictable without adding headcount.
Most manufacturing sites evaluate several options for on-site container handling. Here is how the Mobicon compares across the factors that matter in a production environment.
| Factor | Mobicon Straddle Carrier | Side-Loader | Reach Stacker | Container Forklift |
|---|---|---|---|---|
| Operates Inside a Factory / Warehouse | ✔ From 3.8m door clearance | ✘ No | ✘ No | ~ Limited |
| Separates Delivery from Production Schedule | ✔ Stage containers anytime | ✘ Must unpack on delivery | ✔ Yes | ✔ Yes |
| Eliminates Loading Dock Requirement | ✔ No dock needed | ✔ No dock needed | ✔ No dock needed | ✔ No dock needed |
| Reduces Forklift Traffic and WHS Risk | ✔ Container placed at work point | ✘ Fixed placement only | ~ Partial | ~ Partial |
| Yard Surface Protection | ✔ Lowest axle loads in the world | ~ Variable | ✘ High point loads | ✘ High axle loads |
| Handles Open-Top Containers | ✔ 2T model (bottom-lift) | ~ Limited | ✘ Top-lift only | ✘ Top-lift only |
| Operator Licence Required | ✔ No licence required | ~ Varies | ✘ Licence required | ✘ Licence required |
| Cost Structure | ✔ Fixed capital cost | ✘ Variable per delivery | ~ High CAPEX + running costs | ~ Moderate CAPEX |
Every Mobicon handles standard 20ft and 40ft ISO containers. Models vary by container volume, stacking capability, and indoor clearance requirements, so you invest in what your facility actually needs.
The 2T uses a bottom-lift design that allows it to pass through a standard factory roller door with as little as 3.8 metres clearance. It also handles open-top containers carrying oversized or out-of-gauge loads.
The 2TE is the battery-electric version of the Mobicon 2T. It delivers the same bottom-lift capability and indoor clearance performance with zero exhaust emissions, making it the right choice for enclosed facilities or emission-sensitive sites with lower container volumes.
The 2HL is a top-lift straddle carrier with adjustable height. It works under covered loading bays or awnings with 5.8 metres clearance and stacks one container over another to maximise yard storage between production runs.
The 2HLe delivers full 2HL capability with a battery-electric drivetrain. Zero exhaust emissions and lower running costs make it ideal for enclosed production facilities, ventilation-sensitive sites, or operations with emissions reporting obligations.
The 3H is designed for high-volume manufacturing operations where container throughput is intensive and yard space is limited. Three-high stacking maximises storage density on standard concrete or bitumen surfaces.
The 3HE is the battery-electric version of the Mobicon 3H. It delivers three-high stacking at high throughput with zero exhaust emissions, suited to intensive operations that require maximum yard density alongside sustainability or emissions compliance.
With a Mobicon in the yard, your team decides when containers are packed or unpacked. The container is staged until operations are ready, removing demurrage pressure and the disruption that comes with forced packing windows.
The Mobicon positions containers directly beside your packing station, storage area, or production line. That reduces forklift travel distance, cuts handling time per container, and keeps your team working in one zone.
Every side-loader hire adds a cost you cannot control. A Mobicon converts that variable spend into a single capital investment that stays on-site, available whenever you need it, without booking in advance. Low fuel consumption and low maintenance requirements keep the total running cost predictable over the asset life.
Unlike reach stackers and container forklifts, a Mobicon does not require a separate equipment licence. Trained production or yard staff can operate it, reducing compliance overhead and rostering constraints.
Most container handling equipment is restricted to open yard use. Mobicon straddle carriers are designed to bring the container to a sheltered work area, giving your team a safer and more controlled environment for packing and unpacking regardless of weather conditions.
The 2T is the only compact container handler in its class that can work fully inside a factory building. It passes through a standard industrial roller door and positions the container directly on the warehouse floor for your team to work from.
The 2HL and 2HLe lower their operating height to position containers under covered loading bays or factory awnings with 5.8 metres of clearance. The same machine operates in the open yard or undercover without modification.
Every Mobicon places containers exactly where your production flow requires. Stage near storage racks, alongside packing lines, or at outbound loading points. The container comes to the work, not the other way around.
Loading docks, ramps, and long forklift runs are three of the most common sources of workplace incidents in manufacturing and warehousing. A Mobicon addresses each one directly by changing how containers are handled on-site.
Traditional loading docks require forklifts to transition between ground level and trailer height using ramps that can be slippery, misaligned, or unstable. Removing the dock from the equation removes this hazard entirely. The Mobicon lifts the container off the trailer so no ramp is needed.
When the Mobicon positions a container next to the racking or packing station where goods are stored, forklift operators travel a fraction of the distance they would from a fixed dock. Fewer forklift movements across the yard means less exposure to pedestrian and vehicle conflict.
Packing or unpacking containers outdoors exposes your team to heat, rain, and uneven surfaces. The Mobicon brings the container inside or under cover, so your team works in a consistent, controlled environment. That reduces fatigue-related risk and keeps the work area safer.
Work Health and Safety legislation requires employers to eliminate or minimise foreseeable risks. Replacing loading ramps with a Mobicon is a documented, practical control measure that reduces incident exposure and demonstrates due diligence in your facility's safety management.
The Mobicon uses a hydraulic lifting system with no wire ropes. That eliminates swinging loads and rope hazards entirely, keeping the straddle carrier stable and controlled on slopes and through tight factory yard areas. There are no wire rope inspections to schedule and no replacements to budget for. Safe lifting is built into the machine, not maintained through recurring checks.
When demurrage pressure forces rushed packing under time constraints, forklift operator fatigue and errors increase. By staging containers in the yard and allowing production to set the packing schedule, the Mobicon removes that time pressure and lets operators work at a consistent, safe pace.
Manufacturing yards are not always built to heavy equipment standards. Mobicon's four-axle design produces the lowest axle loads of any container handler in the world, which means it works safely on most standard concrete and bitumen surfaces without requiring upgrades.
Reach stackers and container forklifts concentrate the full combined weight of machine and container across two axles. Over time, that point loading cracks concrete and deforms bitumen surfaces common in manufacturing yards.
The Mobicon spreads that load across four axles using weight-distributing bogies at each corner. Most standard factory yard surfaces handle daily Mobicon operation without pavement upgrades, reducing capital cost and avoiding surface maintenance disruptions.
It is always wise to verify your specific yard surface specification before deploying any container handler. Mobicon Systems can assist with assessing surface suitability as part of the consultation process.
Mobicon Systems backs every unit with a full after-sales programme. Equipment downtime in a manufacturing environment has a direct cost, so support is built into every deployment from day one.
Every Mobicon is backed by a manufacturer's warranty. Your operation has asset confidence from the day the unit is commissioned on site.
Routine servicing can be carried out by any qualified forklift mechanic using locally sourced components. No specialist technician, no proprietary parts, no extended lead times waiting on a service agent.
Mobicon Systems commissions every unit at your facility and includes certified on-site operator training. Your team learns to operate the machine in your actual yard, using your containers and your layout.
When an issue arises, direct telephone support is available to diagnose and resolve problems quickly. Production downtime caused by equipment issues is minimised rather than waiting on a service queue.
For manufacturing sites in regional locations or with critical uptime requirements, Mobicon can include a tailored spare parts package. The right components are on-site before they are needed.
Mobicon Systems offers outright purchase and flexible rental arrangements. Whether you are trialling the equipment before committing or adding to an existing fleet, there is a structure that fits your capital plan.
General Motors Holden previously used a heavy forklift to unload containers at their engine factory. Goods were then loaded onto trolleys so a tractor could transport them to the production floor, because the yard surface could not support the forklift travelling across it.
The double handling added time and increased freight damage through triple handling. After discussions with Mobicon Systems, Holden purchased a Mobicon 2T straddle carrier. The Mobicon now brings loaded containers directly to the factory entrance, eliminating the need for tractors, trolleys, and the double handling that came with them.
"Instead of staff working at a trailer height of 1.5 metres, they are now working at a safe 300mm off the ground. This alone was a major contributing factor for the implementation of the Mobicon."
Wade Price, Distribution and Customer Service Manager, Smorgon Steel Reinforcing QLDTalk to a Mobicon Systems specialist about the right model for your production volumes, facility layout, and WHS requirements. No obligation, just practical advice.
Yes. The Mobicon 2T can pass through a standard industrial roller door with a minimum clearance of 3.8 metres high and 4.6 metres wide. It positions the container on the factory floor so your team can pack or unpack in a sheltered environment without a loading dock.
When a container arrives, the Mobicon lifts it off the trailer and places it in the yard. The driver leaves immediately. When your team is ready, the Mobicon moves the container to the packing area. Your production schedule drives the timing, not the transporter's demurrage clock.
Yes. The Mobicon 2T uses a bottom-lift design, which allows it to handle open-top containers carrying loads that extend above the container rim. The 2HL, 2HLe, and 3H use top-lift frames and are designed for standard ISO containers including hi-cubes.
In most cases, no. Mobicon's four-axle design produces the lowest axle loads of any container handler in the world, making it compatible with standard concrete and bitumen surfaces. We recommend verifying your specific surface specification before deployment, and Mobicon Systems can assist with that assessment.
Loading ramps require forklifts to transition between ground level and trailer height on surfaces that can be slippery or misaligned. A Mobicon places the container at ground level, eliminating the ramp transition entirely. Positioning the container close to where goods are stored also reduces forklift travel distance and the associated pedestrian risk.
No. A Mobicon does not require a separate equipment licence unlike reach stackers and container forklifts. Mobicon Systems provides certified on-site operator training at commissioning so your team is ready to use the machine safely from day one.
Yes. The Mobicon 2HL and 2HLe lower their operating height to work under awnings or covered bays with 5.8 metres of clearance. This lets your team pack and unpack containers out of the weather without requiring a purpose-built enclosed space.
Yes. Mobicon Systems offers flexible rental arrangements alongside outright purchase. A rental gives you the opportunity to assess throughput, site fit, and operator experience before making a capital commitment.
© All rights reserved