A Mobicon is a compact, self-propelled machine that straddles a shipping container, lifts it from within its own frame and carries it around your site. It is a mini straddle carrier built for the end user, not the port. We design and build every unit in Australia for yards, depots and warehouses that move their own containers.
Machine tare weight depends on the model. The 2T weighs 13 tonnes and the 2HL 26 tonnes. These are among the lightest container handlers available, which is what keeps point loads low and protects your yard surface.
A Mobicon has a very low centre of gravity, so unlike a forklift or reach stacker it will not tip over in normal operation. The load is held rigidly by hydraulic cylinders and remote twist locks, with no wire ropes or chains, so a container cannot swing or drop. Staff pack and unpack on the ground, which removes the need for high, slippery loading docks.
Large port straddle carriers, such as those from Kalmar and Konecranes, are built for high-volume terminals and stack up to four containers high. A Mobicon is a light-weight version built for end users who handle their own containers on site. It is smaller, lighter and needs no special yard reinforcement.
Hydraulic wheel motors drive all four axles. A Bosch Rexroth transmission pump is driven by the engine, so there are no mechanical drive axles. Our electric models use the same hydrostatic principle with a battery-electric power unit.
Our light-weight straddle carriers handle a wide range of container types and sizes depending on the model. The bottom-lift 2T handles any ISO container from 20 to 52 feet, plus flat racks, bolsters, half-highs, out-of-gauge and tank containers. A Mobicon also moves containers lengthways, so it needs far less space to manoeuvre than a forklift.
We were founded in 1994 by Tom Schults and are proudly Australian owned, based in Brendale, Queensland. We are now celebrating over 30 years of designing and building light-weight straddle carriers, with units working across Australia, New Zealand, the US, the UK, Europe, Asia and Africa.
Because the load is spread evenly over four axles and eight wheels, the load on the pavement stays very low. Loaded with a 26,000kg container, the 2T has a maximum axle load of only 11,000kg and the 2HL only 13,500kg. Point load, not tyre pressure, is what damages a yard, and our 8-point design gives the lowest point loads of any container handler in the world.
The bottom-lift 2T handles any ISO container from 20 to 52 feet, including flat racks, bolsters, half-highs, open tops, out-of-gauge and tank containers. Our top-lift stacking models, the 2HL and 3H, use a 20 to 40 foot telescopic top spreader and handle any container with standard corner castings at the 20 and 40 foot positions. Most 45-foot units are not compatible with the telescopic spreader, so contact us to confirm any non-standard container.
The 2T has a lift height of 1.75 metres, enough to place a container onto or take it off a trailer. The 2HL lifts high enough to stack two containers high, one high-cube over one high-cube. The 3H stacks three containers high for maximum yard density.
Our 2T, 2HL and 3H each have a 35 tonne safe working load, so they lift fully loaded containers. This is separate from the machine's own tare weight, which stays low to protect your yard.
Our diesel models use a simple 24 volt automotive electrical system, and all cables are tagged for easy fault finding. This keeps diagnostics and repairs straightforward for any qualified mechanic.
Yes. The 2T handles containers loaded up to 800mm out of gauge, which makes it popular in the glass industry. The 2HL can be fitted with an over-height lifting frame to handle a wide range of out-of-gauge loads.
Yes. We offer a battery-electric version of each diesel model. The 2TE, 2HLe and 3HE deliver the same container handling capability with zero on-site emissions, quieter operation and lower running costs. They suit cold storage, enclosed warehouses and sites with strict air quality or noise requirements.
The 2T is 4.5 metres wide externally, with a lowered height of 3.6 metres so it can pass through a standard 4 metre roller door. The 2HL is 4.65 metres wide and works well in a 6 metre laneway. The 3H is 5 metres wide and needs a minimum aisle of 6.5 metres.
Training is required, as with any machinery, but a Mobicon is simple to learn. A structured training session of about three hours is enough for most operators. We recommend using a spotter for the first 50 containers to build confidence and ensure safe operation.
In Australia and most other countries, no forklift or special licence is required to operate a Mobicon. Local regulations must always be checked, as rules differ between regions and can change. We provide competency training as part of commissioning every new unit.
A Mobicon is a one-person operation. The operator lifts, moves, places and locks the container from inside the cabin, with no ground crew needed for the lift.
The cabin sits low and is fitted with a CCTV monitor and four cameras around the machine, giving the operator a safe and comprehensive view. The cabin is contained within the width of the unit, which reduces the risk of cabin damage and the space needed between containers.
The 2T and 2HL travel at 9 km/h, which suits yard and depot work away from the port. High road speed is rarely needed for on-site container movement, so we keep engines and running costs modest.
Unlike container forklifts and reach stackers, which have very high point loads, a Mobicon works on most concrete, bitumen, paver or compacted gravel surfaces. Most surfaces suitable for a truck or trailer suit a Mobicon. If in doubt, we can supply axle weights for different container loads and carry out a yard test.
A Mobicon is serviced every 250 hours or every six months, and a service typically takes about three hours. Most components are comparable with forklift parts, so any qualified forklift mechanic can carry out servicing and most repairs.
Every new Mobicon is backed by a full 2-year or 2,000-hour warranty. Major components, including engine pumps and wheel motors, are covered for an additional 12 months. On-site operator training is included with every purchase.
Our machines are typically used by companies handling between 5 and 200 containers per week, though several clients run higher volumes with multiple units. Industries include logistics and transport, import and export, wine, food, dairy, steel, chemicals and dangerous goods, mining, construction and small ports. The US Navy and Australian Customs also use Mobicon units.
A Mobicon lets you pack and unpack on the ground, which is safer and faster than working at trailer height. Its low axle loads will not damage a standard yard the way forklifts, reach stackers or 1.5 and 2-axle straddle carriers can. Capital, fuel, tyre and maintenance costs are low, and no operator licence is needed. Carrying a 26-tonne container, the 2HL uses about 8 litres of diesel an hour, against up to 21 litres for a comparable reach stacker.
Compared with sideloaders and swing lifters, a Mobicon is more economical as container numbers grow. A sideloader leaves the container where it drops it, while a Mobicon can move containers anywhere on site and place them close to your goods. This reduces truck waiting time, because packing and unpacking no longer depend on the transport provider.
Yes. A low-cost Mobicon can bring container handling in-house, so you control when and where containers are packed and unpacked. Many clients find this reduces 3PL dependency, cuts demurrage and saves both time and money.
We manufacture in Brendale, Queensland, and supply directly across Australia. Internationally we work through distributors including Portstar Machinery in New Zealand and Mitsui E&S in Japan, and we supply the North American market through our US operation.
© All rights reserved